Abstract:
The power source is a battery (bank) is connected to a DC to AC power inverter. The DC to AC power inverter power and electric motor. The electric motor's rotor is connected to the rotor of an alternator with and alternator belt. The alternator is connected to the power source charged at full capacity at all time. The battery bank is then connected to a 2nd 24,000 watt DC to AC power inverter. The power inverters out-put is connected to a transformer for filtering and wave shaping. The transformers is connected to the circuits in the home or industry.
Abstract:
A controller is configured to, while the step-up converter is being controlled in a state where a duty ratio of an on state of an upper arm that is any one of the two switching elements is set to 100% such that the step-up converter does not perform a step-up operation, when a modulation factor of the inverter in voltage modulation exceeds a predetermined modulation factor lower than a step-up command issuance modulation factor at which a step-up command is issued to the step-up converter or when a target voltage at the side of the inverter based on a target operating point of the electric motor exceeds a predetermined voltage lower than the voltage at the side of the electrical storage device, reduce the duty ratio of the on state of the upper arm from 100%.
Abstract:
A trans inductor having a powdery magnetic substance and a power converter using the trans inductor are provided. The trans inductor and the power converter reduce peak current flowing in an inverter power module (IGBT), improve inverter efficiency, reduce output RMS current (output effective current) and reduce capacitor consumption by applying a material with properties that are resistant against current saturation instead of a core material of a conventional trans inductor employed in a power converter. Accordingly, an inductance decreasing rate due to core saturation when high current is generated is improved and current flowing in a switch device is prevented from being abruptly increased.
Abstract:
Embodiments of an integrated motor drive power electronics system are generally described herein. In some embodiments, the integrated motor drive power electronics system includes an active line filter (ALF) configured to control and regulate current drawn from an input power source and to attenuate current ripple fed back to the input power source, an energy storage capacitance coupled to an output of the active line filter, and a bidirectional low voltage power supply (LVPS). In some embodiments, the bidirectional LVPS may provide regulated power to a load and may selectively recycle power back to the input power source and regulate voltage at the load to a predetermined output voltage. In some embodiments, the energy storage capacitance may serve as a local input power source for higher power motor drive electronics and the bidirectional LVPS.
Abstract:
A motor drive system control apparatus includes: a direct current power supply; a three-phase alternating current motor; a first power converter including switching circuits corresponding to each of three phases of the three-phase alternating current motor and a smoothing condenser disposed electrically in parallel with the switching circuits; an estimating device for estimating peak generation timing in which a peak is generated in an inter-terminal voltage VH of the smoothing condenser on the basis of at least one of an operating condition of the three-phase alternating current motor; a switching condition of the switching circuits corresponding to each of the three phases; and a controlling device for controlling a drive condition of the first power converter so the inter-terminal voltage VH (or a VH peak) in the peak generation timing decreases, for a predetermined period from start timing set in a time domain before the estimated peak generation timing.
Abstract:
A LPF extracts DC component of a current detection value of an inverter input current. A subtracting section 4 calculates a difference between a current command value and the DC component of the current detection value. A current controller 5 produces two-phase PWM signals Sa and Sb complementary to each other, from the current difference. Further, an integrating circuit 7 integrates output terminal voltages Vu, Vv and Vw of the inverter to convert the output terminal voltages Vu, Vv and Vw into a magnetic-flux information Φu, Φv and Φw. A logic conversion section 8 converts the magnetic-flux information Φu, Φv and Φw into 120-degree conduction patterns S1′-S6′ to output the 120-degree conduction patterns S1′-S6′. Then, a logic circuit section 9 executes a logic synthesis between the PWM signals Sa and Sb and the 120-degree conduction patterns S1′-S6′ to output gate signals S1-S6.
Abstract:
A three-phase regenerative drive (20) is operated based upon power from a single-phase AC source (12) and power from a DC source (14). The single-phase AC input power and the DC input power are converted to DC voltage on a DC bus (24) by a three-phase converter (22). DC power is provided from the DC bus (24) to a three-phase inverter having outputs connected to a motor (34). A controller (44) controls operation of the three-phase converter (22) based upon contribution factors of the AC and DC sources (12, 14) during motoring and regeneration. The controller (44) also controls an AC component of current from the DC source to reduce ripple current on the DC bus (24).
Abstract:
The control apparatus controls a controlled variable of the electric rotating machine by manipulating an output voltage of a power converter circuit including switching elements operated at a set modulation index to connect positive and negative terminals of a DC power source to corresponding terminals of the electric rotating machine. The control apparatus includes a prediction section configured to predict the controlled variable for each of a plurality of cases where the power converter circuit is set in a corresponding one of a plurality of predetermined operating states, a manipulation section configured to determine one of the predetermined operating states depending on a result of evaluation by an evaluation function, and set the converter circuit to the determined operating state, and a feedback control section configured to feedback-control the output voltage of the power converter circuit at a target value by manipulating the input parameters of the evaluation function.
Abstract:
[Problem] In a pseudo-current source inverter which drives a motor at a high speed, a current phase adjustment is assured and facilitated to perform a field-weakening control or suppress a terminal voltage saturation at a time of the high-speed motor drive.[Means For Solving Problem]A phase advance correction is carried out for a magnetic flux phase information from which a 120 degree conduction pattern is obtained with a motor terminal voltage as a reference phase. The phase advance correction includes the correction of differentiating the terminal voltage detection signals of the motor, the adjustment of enlarging the phase advance correction quantity in a case where the motor load current is large, and delays the gate signals of the 120 degree conduction pattern in accordance with the speed estimation value through a delay counter and carries out the phase advance correction as the rising edge timing of the subsequent gate signal at the subsequent step phase. Furthermore, the error correction is carried out for the phase advance correction quantity in accordance with a variation tendency of the speed estimation value and a detection value of a direct current of the inverter.
Abstract:
A power supply for an electric motor includes a converter that can increase and decrease a voltage supplied into an inverter and then into the stator windings of the motor. As a separate feature, the inverter includes a control coil which is positioned within a motor housing such that it may be cooled by a thermal management system for the motor.